When you would install a new item, you should not forget the steps as to how it will be placed. You should follow them so you can correctly install any Profile Design Cobra bars. This has been required on the policies of its warranty which will be given to the buyer. If you have no knowledge on this, you can ask for help from a dealer nearby.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You have to ensure that its bar clamp diameter would be suitable on its stem diameter. That has to be inspected as it will surely cause a lot of issues in the future. They would not be fit together when their diameters are different. Before an item is purchased, you must look at its diameter for you to prevent any waste of cash on the purchase you would be making.
If you are installing the stem that is new, there are still some instructions from the manufacturer that you should read. Some steps have been set by a manufacturer so you can be certain that it is correctly done. It is indicated on their manual so they can provide that on you so you will not find it difficult on how you can start with that.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You have to ensure that its bar clamp diameter would be suitable on its stem diameter. That has to be inspected as it will surely cause a lot of issues in the future. They would not be fit together when their diameters are different. Before an item is purchased, you must look at its diameter for you to prevent any waste of cash on the purchase you would be making.
If you are installing the stem that is new, there are still some instructions from the manufacturer that you should read. Some steps have been set by a manufacturer so you can be certain that it is correctly done. It is indicated on their manual so they can provide that on you so you will not find it difficult on how you can start with that.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
No comments:
Post a Comment